Minipreps & Plasmid Purification
Learn how to isolate, purify, and analyze plasmid DNA from bacterial cultures using the alkaline lysis miniprep method.
This comprehensive guide walks you through each stage of plasmid purification, from harvesting bacterial cells and separating plasmid DNA from chromosomal DNA to DNA precipitation, washing, and resuspension.
You'll also learn how to prepare the required buffers and reagents, measure DNA concentration and purity using spectrophotometry or a NanoDrop, and evaluate your results through agarose gel electrophoresis.
The guide also covers DNA fragment purification from agarose gels using a simple cotton filtration method, providing an overview of techniques used to prepare DNA for downstream applications such as PCR, restriction enzyme digestion, and molecular cloning.
How It Works
A miniprep is the isolation and purification of plasmid DNA from a small (~1-3ml) sample of cells, usually bacterial cells. Plasmid DNA is a small circular piece of DNA that is foreign with respect to the cell type (usually bacterial cells); this is different from the cell’s own chromosomal DNA. Thus, the plasmid DNA needs to be purified separately from the chromosomal DNA. While there are commercially available kits for prepping plasmid DNA, it’s also very possible & easy to do using homemade buffers.
The following protocol is an alkaline lysis method used for purifying DNA from a ~3ml liquid culture of bacterial cells. The method relies on the fact that, under alkaline (pH = 11) conditions, both plasmid and chromosomal DNA are denatured; subsequent neutralization with the high salt buffer potassium acetate in the presence of SDS causes the cell’s chromosomal DNA and proteins to form an insoluble aggregate, while the plasmid DNA stays in solution. Spinning the sample in a microcentrifuge separates these insoluble aggregates from the soluble plasmid in solution. Alternatively, addition of pure chloroform and subsequent centrifugation will cause the plasmid DNA to separate into a different phase from the rest of the components of the cell. The plasmid DNA is then itself precipitated into a pellet using isopropanol, washed in ethanol, and resuspended in pure water.
The DNA purified here can be used for restriction enzyme digestion or amplification by PCR.
Step: 1
Reagents &
Buffer Preparation
Reagents:
Recipes:
Step: 2
Miniprep
(Alkaline Lysis Method)
Pellet cells by spinning in a microcentrifuge at 12,000rpm for 2min. at room temp. (~25°C).
Warning:
Resuspend cell pellet in 100ul TEG buffer: vortex until there are no more clumps.
Chill on ice for about a minute.
Set vortex to lowest setting and carefully hold tube, uncapped, on the vortex with one hand, making sure the buffer inside is actually spinning around without going out of the tube; with the other hand, add 200ul NaOH/SDS buffer one drop at a time while vortexing gently.
Incubate on ice 5min.
Add 150ul KOAc buffer and invert 6X to mix gently.
Incubate on ice 5min.
Warning:
Spin in microcentrifuge at 12,000rpm for 5min. at room temp.
Carefully transfer supernatant to a fresh microtube.
Warning:
Add 1ml 100% isopropanol and invert 6X to mix gently.
Incubate at room temp 2min.
Spin in microcentrifuge at 12,000rpm for 10min. at room temp.
Remove supernatant carefully without disturbing the DNA pellet.
Wash the DNA pellet by adding 1ml 70% ethanol.
Spin in microcentrifuge at 12,000rpm for 10min. at room temp.
Remove as much supernatant as possible without disturbing the pellet.
Allow DNA pellet to dry completely, about 15-30min.
Warning:
Resuspend pellet in 50ul DW/RNase and mix by pipetting up and down a few times, without introducing any bubbles.
Let the reconstituted DNA sit at room temp. for at least 10min. before moving on.
DNA Quantification
DNA is classically quantified by spectrophotometric absorption at wavelengths of 260nm and 280nm. The ratio of absorption at 260/280 gives a reading of the purity of the DNA; pure DNA should have a 260/280 ratio of 1.8, while pure RNA will have a 260/280 ratio of 2.0.
Contamination with chloroform or proteins will cause this ratio to deviate from these values significantly. The more modern nanodrop can also give DNA concentration and purity measurements.
Whichever you choose, it should be able to do it for you; but generally:
Say you diluted your sample 1:50 by adding 1ul of undiluted sample + 49ul of buffer for 50ul total, and you read the absorbance of this 1:50 diluted sample at 260nm and 280nm wavelengths.
The A260 = 0.2108 and the A280 = 0.1146.
The concentration of the undiluted sample is then:
The A260/A280 = 1.84, indicating fairly pure DNA.
If you don’t have access to a spectrophotometer, you can also run a sample of your DNA on an agarose gel and compare with a DNA standard of known concentration.
For example, if you load 10ul of your DNA on a gel and notice that the band intensity is roughly equivalent to the DNA standard, which you know is 100ng, then you can assume that 10ul of your sample contains 100ng; this works out to be 10ng/ul, or 10ug/ml.
Gel Visualization
& Purification
Following plasmid DNA purification, the minipreps can be analyzed by various methods. Two main methods in classical molecular cloning are restriction enzyme digestion and PCR amplification.
Both methods produce fragments that need to be purified. The fragments can be subjected to agarose gel electrophoresis, and the band at the correct/expected size can be excised from the gel and purified.
While purification can be performed with a commercially available kit with >80% recovery (QIAquick Gel Extraction kit, Qiagen), a simple method utilizing cotton filtration with ~30-60% recovery may be sufficient for most downstream cloning applications.
Step: 3
Agarose Gel Purification
Warning:
Pierce a 0.5ml microtube from the inside with a 22-gauge needle.
Insert absorbent cotton (for example, from cotton swabs) into the bottom of the 0.5ml microtube, up to the 200ul mark, loosely.
Run the digested DNA or PCR reaction on an agarose gel.
Safely visualize the bands.
Protecting your eyes and skin, cut the desired band(s) with a clean, sharp razor and place gel slice into the 0.5ml microtube, on top of the cotton cushion (slice should ideally include only the DNA band, ~2mm x 10mm max).
Warning:
Cap the 0.5ml microtube and place into a 1.7ml microtube adaptor tube without a lid; spin in a microcentrifuge at room temp. according to the size of the fragment:
Remove the 0.5ml microtube; there should be ~15-30ul of recovered DNA in the gel-making buffer.
Warning:
Citations
Sun, Y., Sriramajayam, K., Luo, D., Liao, D.J. (2012) A quick, cost-free method of purification of DNA fragments from agarose gel. J Cancer 3:93-95. doi: 10.7150/jca.4163.
Build Your Own Molecular Biology Lab
Set up your own molecular biology workspace with the Complete Genetic Engineering Lab Kit, featuring essential equipment, reagents, and biological materials for DNA preparation, bacterial culture, and genetic engineering.
Expand your setup with optional equipment, including a PCR machine and gel electrophoresis system.